Electrolux Manual For Over The Range Microwave
High standards of quality at Electrolux Home Products, Inc.
mean we are constantly working to improve our products.
We reserve the right to change specifications or
discontinue models without notice.
electrolux Major appliances, n.a.
usa
•
10200 David Taylor Drive
•
Charlotte, NC 28262
•
1-877-4electrolux (1-877-435-3287)
•
electroluxappliances.com
canada
•
5855 Terry Fox Way
•
Mississauga, ON L5V 3E4
•
1-800-265-8352
•
electroluxappliances.ca
EI30SM35Q 02/14
© 2014 Electrolux Home Products, Inc.
* Can NOT be installed
in island or peninsula
cabinet arrangements
Over-the-Range Microwave
EI30SM35Q
29
7
/
8
'
15
1
/
32
'
rear
extrusion
lower
extrusion
Power cord
location
Blower plate allows for vertical
or horizontal ducting
Allow at least 26' clearance
for door depth when open
16
13
/
32
'
Backsplash
12'
min.
13'
max.
2' min.
Rear Wall
16
1
/
2
' min.
30' min.
66' min.
from floor
to top of
microwave
Bottom edge of
cabinet MUST be
30' min. from
cooking surface
Cabinet MUST be
capable of
supporting a total
load of 150 lbs.
30'
min.
Microwave MUST
Jan 1, 2006 - (1) Akta ini bolehlah dinamakan Akta Senjata Api (Penalti. Lebih Berat) 1971. Membawanya, bersalahan dengan Akta Senjata 1960. Akta senjata api 1960 pdf. No information is available for this page.Learn why.
be mounted to
BOTH a top cabinet
AND a wall*
Locate 120V/60Hz grounded outlet inside upper cabinet
30' Over-the-range Microwave specifications
•
Product Weight – 64 Lbs.
•
Voltage Rating – 120V / 60 Hz / 15 Amps
•
Connected Load (kW Rating) @ 120 Volts = 1.6 kW
(For use on adequately wired 120V, dedicated circuit having 2-wire
service with a separate ground wire. Appliance must be grounded for safe
operation.)
•
Amps @ 120 Volts = 15 Amps
•
Always consult local and national electric codes.
•
Grounded outlet should be located in cabinet above, with hole in base to
route power cord. Carefully follow top template instructions for power cord
clearance when installing beneath smooth, flat cabinets.
•
Microwave’s ventilation system is preset to recirculate air inside with no
ducting system required. Exhausting air outside is optional, using either
vertical or horizontal ducting system. (Refer to Ducted Option Specifications
for outside ventilation.)
•
For safe and proper installation, microwave MUST be mounted to BOTH
a top cabinet AND a wall, and connected to at least one wall stud. Can NOT
be installed in island or peninsula cabinet arrangements.
•
Cabinet bottom MUST be level to insure proper installation.
•
Cabinet MUST be capable of supporting a total load of 150 lbs.
•
Filler blocks recommended for installation when cabinet front hangs below
recessed bottom shelf.
•
Minimum distance of 30' required from cooking surface to bottom edge
of top cabinet.
•
Minimum distance of 66' required from floor to top of microwave.
•
Opening between cabinets MUST be 30' wide and free of obstructions.
For openings up to 36' wide, order optional 36' Filler Kit to fill in gap
between unit and cabinets.
•
Allow 26' minimum clearance for 90° door swing.
ducted Option specifications
•
For outside ventilation.
•
Exhaust duct adapter will be needed for outside ventilation, to mate with
standard 3-1/4' x 10' rectangular duct. If round duct required, rectangular-
to-round transition adapter will be needed with no more than 6' diameter.
•
For most efficient airflow exhaust, use a straight run or as few elbows
as possible with a maximum duct length of 3-1/4' x 10' rectangular or
6' diameter round duct, not to exceed 120 equivalent feet.
•
For horizontal installation, be sure to allow enough space between wall
studs to accommodate exhaust.
•
Refer to installation instructions on web for detailed duct preparation and
converting exhaust vent blower system for exterior exhaust ventilation.
Note: For planning purposes only. Refer to Product Installation Guide
on the web at electroluxappliances.com for detailed instructions.
Optional accessories
•
36' Filler Kit: S – (PN # MWFILKTSS).
Over-the-range MicrOwave
EI30SM35QS
Summary of the content on the page No. 1
Installation Instructions
Over the Range Microwave Oven
BEFORE YOU BEGIN
Read these instructions completely and carefully.
� Note to Consumer – Keep these instructions for
future reference.
• IMPORTANT – Save these instructions for
� Skill level – Installation of this appliance requires
local inspector’s use.
basic mechanical and electrical skills.
� IMPORTANT – Observe all governing codes
� Proper installation is the responsibility of the
and ordinances.
installer.
� Note to Installer – B
Summary of the content on the page No. 2
Installation Instructions CONTENTS C Outside Back Exhaust............... 18–21 General information Preparing Rear Wall ................ 18 Important Safety Instructions ...........3 Attach Mounting Plate to Wall ...... 18, 19 Electrical Requirements ...............3 Preparation of Top Cabinet ........... 19 Hood Exhaust ......................4, 5 Adjust Blower .................. 19, 20 D
Summary of the content on the page No. 3
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS This product requires a three-prong grounded outlet. You should have the wall receptacle and circuit The installer must perform a ground continuity check checked by a qualified electrician to make sure on the power outlet box before beginning the the receptacle is properly grounded. installation to insure that the outlet box is properly grounded. If not properly grounded, or if the outlet Where a standard two-prong wall receptacle is
Summary of the content on the page No. 4
Installation Instructions HOOD EXHAUST NOTE: Read these next two pages only if you plan to vent your exhaust to the outside. If you plan to recirculate the air back into the room, proceed to page 11. OUTSIDE TOP EXHAUST (EXAMPLE ONLY) The following chart describes an example of one possible ductwork installation. DUCT PIECES EQUIVALENT NUMBER EQUIVALENT LENGTH x USED = LENGTH Roof Cap 24 Ft. x (1) = 24 Ft. 12 Ft. Straight Duct (6' 12 Ft. x (1) = 12 Ft. Round) Rectangular-to-Round 5 Ft. x (1) =
Summary of the content on the page No. 5
Installation Instructions NOTE: If you need to install ducts, note that the total Maximum duct length: duct length of 3¼' x 10' rectangular or 6' diameter For satisfactory air movement, the total duct length of round duct should not exceed 140 equivalent feet. 3¼' x 10' rectangular or 6' diameter round duct Outside ventilation requires a HOOD EXHAUST should not exceed 140 equivalent feet. DUCT. Read the following carefully. Elbows, transitions, wall and roof NOTE: It is important that ven
Summary of the content on the page No. 6
Installation Instructions Installation Instructions DAMAGE – SHIPMENT/ PARTS INCLUDED INSTALLATION HARDWARE PACKET � If the unit is damaged in shipment, return the unit to the store in which it was bought for repair PART QUANTITY or replacement. Wood Screws 1 � If the unit is damaged by the customer, repair (¼' x 2') or replacement is the responsibility of the customer. Toggle Bolts 3 � If the unit is damaged by the installer (if other (and wing nuts) than the customer), repair or replace
Summary of the content on the page No. 7
Installation Instructions TOOLS YOU WILL NEED Ruler or tape measure and straight edge Carpenter square (optional) Pencil # 1 and #2 Phillips screwdriver Tin snips (for cutting Scissors 3 Electric drill with /16', ½' damper, if required) Filler blocks or scrap wood (to cut template, if necessary) 5 and /8' drill bits pieces, if needed for top cabinet spacing (used on recessed bottom cabinet installations only) Saw (saber, hole or keyhole) Gloves Stud finder or Hammer (optional) Safety go
Summary of the content on the page No. 8
Installation Instructions 1.PLACEMENT OF THE MOUNTING PLATE A. REMOVING THE MICROWAVE B. FINDING THE WALL STUDS OVEN FROM THE CARTON/ REMOVING THE MOUNTING PLATE 1. Remove the installation instructions, Exhaust adaptor, filters, glass tray and the small hardware Wall Studs bag. Do not remove the Styrofoam protecting the front of the oven. Center 2. Fold back all 4 carton flaps fully against carton sides. Then carefully roll the oven and carton over onto the top side. The oven should be res
Summary of the content on the page No. 9
At least 30″ Installation Instructions C. DETERMINING WALL PLATE LOCATION UNDER YOUR CABINET Plate position – beneath framed recessed Plate position – beneath flat bottom cabinet cabinet bottom 16-1/2² C C L Draw a vertical line on L 33″ to Cooktop the wall at the center of the 30″ wide space. Tape the Rear Wall Draw a vertical line on the wall at the center of the Template onto the wall 30″ space. matching the centerline Tape the Rear Wall Template onto the wall and touching the mat
Summary of the content on the page No. 10
Installation Instructions D. ALIGNING THE WALL PLATE Hole A Draw a Vertical Line Centerline on Wall from Center notches of Top Cabinet C L Horizontal Line Area E Horizontal Line Hole C Hole B Draw a Horizontal line on wall from bottom of “Rear Wall Template”. CAUTION: Wear gloves to avoid cutting fingers on sharp edges. 1. Draw a Vertical line on the wall at the center of the 30' wide space. NOTE: Holes A, B and C are inside area E. If none of A, B and C is in a stud, find a stud somewhere
Summary of the content on the page No. 11
Installation Instructions 2. INSTALLATION TYPES (Choose A, B or C) This microwave oven is designed for adaptation to NOTE: This microwave is shipped after being the following three types of ventilation: assembled for “Recirculating”. And exhaust adaptor is shipped assembled to the filler-upper. Select the A. Recirculating (Non-Vented Ductless) type of ventilation required for your installation and B. Outside Top Exhaust (Vertical Duct) proceed to that section. C. Outside Back Exhaust (Horizo
Summary of the content on the page No. 12
Installation Instructions A. RECIRCULATING (Non-Vented Ductless) INSTALLATION OVERVIEW A1. Attach Mounting Plate to Wall A2. Prepare Top Cabinet A3. Mount the Microwave Oven A1. ATTACH THE MOUNTING PLATE 3. Place the mounting plate against the wall and insert the toggle wings into the holes in the wall to TO THE WALL mount the plate. NOTE: Before tightening toggle bolts and wood screw, make sure to coincide bottom line of the Mounting plate with Horizontal line of “Rear wall Template” and t
Summary of the content on the page No. 13
Installation Instructions especially when mounting flush to bottom of A3. MOUNT THE MICROWAVE OVEN cabinet. Cabinet Front Cabinet Bottom Shelf Filler Block Equivalent to Depth of Cabinet Recess FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE Self-Aligning Screw INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during Microwave Oven Top installation. NOTE: If your cabinet is metal, use the nylon 4. Attach the microwave oven to the top cabinet. grom
Summary of the content on the page No. 14
Installation Instructions B. OUTSIDE TOP EXHAUST (Vertical Duct) INSTALLATION OVERVIEW B1. Attach Mounting Plate to Wall B2. Prepare Top Cabinet B3. Adjust Blower B4. Check Damper Operation B5. Mount Microwave Oven B6. Adjust Exhaust Adaptor B7. Connect Ductwork B1. ATTACH THE MOUNTING PLATE To use toggle bolts: TO THE WALL Spacing for Toggles More Than Wall Thickness Toggle Wings Toggle Mounting Bolt Plate Wall Bolt End 3. Place the mounting plate against the wall and Attach the plate to th
Summary of the content on the page No. 15
Installation Instructions B3. ADAPTING MICROWAVE B2. USE TOP CABINET TEMPLATE FOR PREPARATION OF TOP BLOWER FOR OUTSIDE TOP CABINET EXHAUST You need to drill holes for the top support screws, a 1. Remove and save 2. Lift up the hole large enough for the power cord to fit through, screw that holds blower plate. and a cutout large enough for the exhaust adaptor. blower plate to microwave. Blower Plate Back of Microwave Screw 3. Carefully pull out the blower unit. The wires will extend
Summary of the content on the page No. 16
Installation Instructions B5. MOUNT THE MICROWAVE OVEN AFTER: Fan Blade Openings Facing Upward FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. IMPORTANT: Do not grip or use handle during 5. Place the blower unit back into the opening. installation. NOTE: If your cabinet is metal, use the nylon grommet around the power cord hole to prevent cutting of the cord. NOTE: We recommend using filler blocks if the cabinet front hangs below the
Summary of the content on the page No. 17
Installation Instructions B5. MOUNT THE MICROWAVE OVEN B6. ADJUST THE EXHAUST ADAPTOR (cont.) Open the top cabinet and adjust the exhaust adaptor to connect to the house duct. Cabinet Front Cabinet Bottom Shelf Back of Damper Microwave Blower-Plate Filler Block Equivalent to Depth of Cabinet Recess For Front-to-Back Self-Aligning Screw Adjustment, Slide the Exhaust Adaptor as Microwave Oven Top Needed 4. Attach the microwave oven to the top cabinet. 5. Insert 2 self-aligning screws B7.
Summary of the content on the page No. 18
Installation Instructions C. OUTSIDE BACK EXHAUST (Horizontal Duct) INSTALLATION OVERVIEW C1. Prepare Rear Wall C2. Attach Mounting Plate to Wall C3. Prepare Top Cabinet C4. Adjust Blower C5. Mount the Microwave Oven C1. PREPARING THE REAR WALL C2. ATTACH THE MOUNTING PLATE FOR OUTSIDE BACK EXHAUST TO THE WALL You need to cut an opening in the rear wall for outside exhaust. Attach the plate to the wall using toggle bolts. At least one wood screw must be used to attach the plate to a wall stud
Summary of the content on the page No. 19
Installation Instructions C2. ATTACH THE MOUNTING PLATE C4. ADAPTING MICROWAVE BLOWER TO THE WALL (cont.) FOR OUTSIDE BACK EXHAUST 1. Remove and save screw that holds blower Plate To use toggle bolts: to microwave. Spacing for Toggles More Blower motor Than Wall Thickness screw. 2. Lift up the Blower Plate. Toggle Wings Mounting Toggle Blower Motor Plate Bolt Back of Microwave Wall Bolt End Blower Motor Screw 3. Place the mounting plate against the wall and 3. Carefully pull out the blo
Summary of the content on the page No. 20
Installation Instructions 6. Place the blower unit back into the opening. C5. MOUNT THE MICROWAVE OVEN AFTER: Fan Blade Openings Facing Back End A End B FOR EASIER INSTALLATION AND PERSONAL SAFETY, WE RECOMMEND THAT TWO PEOPLE INSTALL THIS MICROWAVE OVEN. CAUTION: Do not pull or stretch the blower unit IMPORTANT: Do not grip or use handle during wiring. Make sure the wires are not pinched. installation. NOTE: The blower unit exhaust openings should NOTE: If your cabinet is metal, use the